CANopen Master Series

1 Port Intelligent DeviceNet Master Communication Board with DeviceNet Firmware Inside

● DeviceNet Version: Volume I & II, Release 2.0
● Programmable Master MAC ID and Baud Rate
● Baud Rate: 125 kbps, 250 kbps, 500 kbps
● Support Group 2 and UCMM connection
● I/O Operating Modes: Poll, Bit-Strobe, Change of State / Cyclic
● I/O Length: 512 Bytes max (Input/Output) per slave
● Slave Node : 63 nodes max
● Support Auto-Search slave device function
● Support on-line adding and removing devices
● Support Auto-detect Group 2 and UCMM device

1 Port Intelligent DeviceNet Master Communication Board with DeviceNet Firmware Inside

● DeviceNet Version: Volume I & II, Release 2.0
● Programmable Master MAC ID and Baud Rate
● Baud Rate: 125 kbps, 250 kbps, 500 kbps
● Support Group 2 and UCMM connection
● I/O Operating Modes: Poll, Bit-Strobe, Change of State / Cyclic
● I/O Length: 512 Bytes max (Input/Output) per slave
● Slave Node : 63 nodes max
● Support Auto-Search slave device function
● Support on-line adding and removing devices
● Support Auto-detect Group 2 and UCMM device

CANopen Firmware Inside and One Standalone Intelligent CAN Communication Board

● NMT: Master
● CANopen Version: DS-301 v4.02
● Error Control: Support Guarding protocol
● Support EMCY receiving
● Provide dynamic PDO functions
● Provide 5 sets of SYNC cyclic transmission
● Transmission type of PDO is supported
● Support Multi-Master to Single-Slave architecture
● Auto select with expedition mode or segment mode
● Support Windows 2K/XP

CANopen Firmware Inside and One Standalone Intelligent CAN Communication Board

● NMT: Master
● CANopen Version: DS-301 v4.02
● Error Control: Support Guarding protocol
● Support EMCY receiving
● Provide dynamic PDO functions
● Provide 5 sets of SYNC cyclic transmission
● Transmission type of PDO is supported
● Support Multi-Master to Single-Slave architecture
● Auto select with expedition mode or segment mode
● Support Windows 2K/XP

PCI Express CAN Communication Card

● PCI Express Interface
● Compatible with CAN 2.0 parts A and B
● Fully compatible with ISO 11898-2 standard
● Support CAN bard from 10K to 1M bps
● 2500Vrms photo couple isolation on the CAN bus
● Universal PCI supports both 5V and 3.3V PCI bus
● Build-in jumper to select 120 ohm terminal resister
● 3KV galvanic isolation
● 2 independent CAN channels
● Direct memory mapping to the CAN controller

PCI Express CAN Communication Card

● PCI Express Interface
● Compatible with CAN 2.0 parts A and B
● Fully compatible with ISO 11898-2 standard
● Support CAN bard from 10K to 1M bps
● 2500Vrms photo couple isolation on the CAN bus
● Universal PCI supports both 5V and 3.3V PCI bus
● Build-in jumper to select 120 ohm terminal resister
● 3KV galvanic isolation
● 2 independent CAN channels
● Direct memory mapping to the CAN controller

PCI Express CAN Communication Card

● PCI Express Interface
● Compatible with CAN 2.0 parts A and B
● Fully compatible with ISO 11898-2 standard
● Support CAN bard from 10K to 1M bps
● 2500Vrms photo couple isolation on the CAN bus
● Universal PCI supports both 5V and 3.3V PCI bus
● Build-in jumper to select 120 ohm terminal resister
● 3KV galvanic isolation
● 2 independent CAN channels
● Direct memory mapping to the CAN controller

PCI Express CAN Communication Card

● PCI Express Interface
● Compatible with CAN 2.0 parts A and B
● Fully compatible with ISO 11898-2 standard
● Support CAN bard from 10K to 1M bps
● 2500Vrms photo couple isolation on the CAN bus
● Universal PCI supports both 5V and 3.3V PCI bus
● Build-in jumper to select 120 ohm terminal resister
● 3KV galvanic isolation
● 2 independent CAN channels
● Direct memory mapping to the CAN controller

2-Port Isolated Protection Universal PCI CAN Card with 5-Pin Screw Terminal Connector

● Two independent CAN bus 2.0A/2.0B communication ports
● Compatible with CAN specification 2.0 parts A and B
● On-board optical isolation protection
● Programmable transfer rate up to 1 Mbps
● Jumper select 120Ω terminator resistor for each port
● Direct memory mapping to the CAN controllers
● 33MHz 32bit 5V PCI bus (V2.1) plug and play
● Universal PCI card, supports both 5V and 3.3V PCI bus

2-Port Isolated Protection Universal PCI CAN Card with 9-Pin D-Sub Connector

● Two independent CAN bus 2.0A/2.0B communication ports
● Compatible with CAN specification 2.0 parts A and B
● On-board optical isolation protection
● Programmable transfer rate up to 1 Mbps
● Jumper select 120Ω terminator resistor for each port
● Direct memory mapping to the CAN controllers
● 33MHz 32bit 5V PCI bus (V2.1) plug and play
● Universal PCI card, supports both 5V and 3.3V PCI bus

2-Port Isolated Protection CAN Communication Board with 5-Pin Screw Terminal Connector

● Two independent CAN bus 2.0A/2.0B communication ports
● Compatible with CAN specification 2.0 parts A and B
● On-board optical isolation protection
● Programmable transfer rate up to 1 Mbps
● Jumper select 120Ω terminator resistor for each port
● Direct memory mapping to the CAN controllers
● 33MHz 32bit 5V PCI bus (V2.1) plug and play
● PCI card, supports 5V PCI bus

2-Port Isolated Protection CAN Communication Board with 9-Pin D-Sub Connector

● Two independent CAN bus 2.0A/2.0B communication ports
● Compatible with CAN specification 2.0 parts A and B
● On-board optical isolation protection
● Programmable transfer rate up to 1 Mbps
● Jumper select 120Ω terminator resistor for each port
● Direct memory mapping to the CAN controllers
● 33MHz 32bit 5V PCI bus (V2.1) plug and play
● PCI card, supports 5V PCI bus

● NMT: Master
● CANopen Version: DS-301 v4.02
● Error Control: Node Guarding protocol
● Allow EMCY receptions
● Provide dynamic PDO functions
● Fully compliant with USB 1.1/2.0 (Full Speed)
● Support SYNC protocol
● Several transmission types of PDO are supported
● Support SDO download/upload segment protocol
● PWR, ACT, ERR, and Tx/Rx LED indicator