Ga naar het einde van de afbeeldingen-gallerij

Ga naar het begin van de afbeeldingen-gallerij

ICS Parallel Digital Interface Module 2363

Levertijd:

3~4 weken

SKU

2363

RS-232/RS-485 to Parallel Digital Interface Module

● Provides a user-definable parallel interface with bit, byte and string data transfer capabilities. Fully configurable to the user's needs by bus commands.
● Signal monitor feature detects signal changes. Relieves controller of time consuming polling function.
● High-current drivers and input pullup resistors. Drives larger loads and inputs CMOS signals or contacts.
● Programmable RS-232 and RS-485 serial interfaces. Supports point-to-point or network connections.
● Provides IEEE-488.2 Status Structure and SCPI parser. GPIB functionality over a serial link.
● Device setup and network address stored in Flash. Stored setup eliminates program initialization statements.
● Includes a menu-driven configuration program. Steps user through configuration choices.

Brochure EN

Details

ICS Parallel Digital Interface Module 2363 is a compact, RS-232/RS-485 to Parallel Interface that provides 48 programmable digital lines that can be configured as inputs or outputs in eight bit bytes. As inputs, each data line has a pullup resistor for sensing contact closures or TTL/CMOS inputs. As outputs, each line is latched and can source 24 mA or sink up to 48 mA. The ICS Parallel Digital Interface Module 2363 can also be configured to monitor up to 15 input lines for changes. Applications include interfacing devices with parallel digital signals to a serial link, controlling discrete devices, and monitoring digital signals for changes.

SPECIFICATIES

Meer informatie

Art.nr.

2363

Fabrikant

ICS Electronics

Land van herkomst

Verenigde Staten

Interface Specifications

Provides RS-232 full duplex and RS-485 (RS-422) half duplex asynchronous serial interfaces. Unit automatically responds to the serial interface that receives the command.

RS-232 Interface

Signals	AB, BA and BB
Mode	Full Duplex

RS-485 (RS-422) Signals

Signals	TX/RX pair
Mode	Half duplex with or without address detection
Addresses	0 ~ 15
Termination	220 Ω load resistor and 1 KΩ pullup/pulldown resistors

Data Rates and Formats

Baud Rate	1200 ~ 115.2 Kbaud
Data Bits	7 or 8
Stop Bits	1 or 2
Parity	Odd, Even or None

Command Sets

SCPI and short form commands plus the following IEEE 488.2 Common Commands:

*CLS, *ESE, *ESE?, *IDN?, *OPC, *OPC?, *PSC, *PSC?, *RCL, *RST, *SAV, *SRE, *SRE?, *TRG, *TST and *WAI.

Digital I/O

2363's parallel I/O signals have the following electrical characteristics. All time delays listed here are maximums, all pulse widths are minimums.

Lines

48 Digital I/O plus 2 Status Inputs

Input Logic Levels

High = > +2.0 V @ ±10 μA

Low = <0.8 V @ 250 μA

with 33 KΩ pullup to +5 VDC for sensing contacts

Max High = 5.5 V

Input Timing

External Data Inhibit line SETS within 1 μs of the active edge of the EDR Input signal and resets after data is loaded. Data loading time for 6 BCD/HEX characters is 0.15 ms (typ.) after the 2363 has been addressed as a Talker.

Output Logic Levels

High = >3 V with 3 mA source

High =>2 V with 24 mA source

Low = 0.0 to +0.55 Vdc, 48 mA sink

Output Timing

Data is transferred to the output 0.7 to 6 ms after receipt of a terminator depending upon transfer method.

Data Stb

Output pulse width, 7 μs

Trigger

Output pulse width, 7 μs

Clear

Output pulse width, 7 μs

Reset

Output pulse width, 50 μs for *RST command and true during 2363 reset time (70 ms)

Controls and Indicators

Controls
POWER	Front-panel switch energizes unit
Indicators
PWR	Indicates power on
RDY	Unit has passed self test
TX	Unit is transmitting
RX	Unit is receiving
SRV	Unit sent Service Request Message
ERR	Unit has detected a command error

Grootte

1185.2 x 38.6 x 189.2mm (W x H x D)

Connectors and Headers

Serial	25-pin female, metal DB shell with lock studs
I/O	62-pin female, metal DC shell connector with lock studs
Serial Header	10-pin male
LED Header	8-pin male

Omgeving

Operating Temperature	-10 °C to +55 °C
Storage Temperature	-40 °C to +70 °C
Humidity	0-90% RH no condensation

Power

9 to 32 VDC @ 3 VA

Mechanical

Construction

All metal case shields RFI

Included Accessories

Instruction Manual
Configuration Disk
UL/CSA/VDE/CE approved AC power adapter
Mating 62-pin connector and hood

Stel uw vraag

U bent wellicht ook geïnteresseerd in de volgende producten:

ICS Parallel Digital Interface Module 2363

Laatste nieuws