ICPDAS PET-7217-10
PoE Ethernet I/O Module with 2-port Ethernet Switch and 10/20 Analog inputs (RoHS)
● Built-in Web Server
● Web HMI
● Support for both Modbus TCP and Modbus UDP Protocols
● Communication Security
● Dual Watchdog
● Wide Operating Temperature Range: -25 ~ +75°C
● I/O Pair Connection
● Built-in I/O
●AI: 10/20 Channels with 240 Vrms Overvoltage Protection
The PET-7217-10, PoE Ethernet I/O Module with 2-port Ethernet Switch, is a module with 10-channel differential or 20-channel single-ended analog inputs. It provides programmable input range on all analog channels (+/-150 mV, +/-500 mV, +/-1 V, +/-5 V, +/-10 V, +/-20 mA, 0 ~ 20 mA and 4 ~ 20 mA). Each analog channel is allowed to configure an individual range and has 240 Vrms high overvoltage protection. Each analog input can be programmed to accept voltage or current as input depending upon the position of corresponding jumper.
The sampling rate of PET-7217-10 has two modes; fast mode and normal mode for your consideration. The PET-7217-10 also has qualification for 4 kV ESD protection as well as 3000 VDC intra-module isolation.
| Built-In Web Server | Yes |
| Web HMI | Yes |
| I/O Pair Connection | Yes |
| Ethernet Port | 10/100 Base-TX with Auto MDI/MDI-X |
| Protocol | Modbus/TCP, Modbus/UDP |
| Security | ID, Password and IP Filter |
| Dual Watchdog | Yes, Module (0.8 seconds), Communication (Programmable) |
| Analog Input | ||
| Channels | 10 differential or 20 single-ended (Note1), | |
| software selectable | ||
| Type | +/-150 mV, +/-500 mV, +/-1V, +/-5V, +/-10V | |
| +/-20 mA ,0 ~ 20 mA, 4 ~ 20 mA | ||
| (Jumper Selectable) | ||
| Individual Channel Configuration | Yes | |
| Resolution | 16-bit | |
| Sampling Rate | Normal Mode | 10 Samples/Second (Total) |
| Fast Mode | 50 Samples/Second (Total) | |
| Accuracy | Normal Mode | +/-0.1% |
| Fast Mode | +/-0.5% or better | |
| Zero Drift | +/-20 μV/°C | |
| Span Drift | +/-25 ppm/°C | |
| Overvoltage Protection | Differential | 240 Vrms |
| Single-ended | 150 Vrms | |
| Common Voltage Protection | ±200 VDC | |
| Overcurrent Protection | Yes, 50 mA at 110 VDC | |
| Virtual Channel to Channel Isolation | Yes, 400 VDC | |
| Open Wire Detection for 4 ~ 20 mA | Yes | |
| Input Impedance | Voltage | 2 MΩ (Differential), 1 MΩ (Single-ended) |
| Current | 125 Ω | |
| Common Mode Rejection | 86 dB Min. | |
| Normal Mode Rejection | 100 dB | |
| Note1: Differential mode can be used for voltage input and current input. Single-Ended mode can be used for voltage input only. | ||
| Ethernet | 1500 VDC |
| I/O | 2500 VDC |
| ESD (IEC 61000-4-2) | 4 kV Contact for each terminal and 8 kV Air for random point |
| EFT (IEC 61000-4-4) | ±4 kV for Power |
| Surge (IEC 61000-4-5) | ±4 kV for Power |
| L1 | System Running |
| L2 | Ethernet Link/Act |
| L3 | Ethernet 10/100 M Speed |
| Reverse Polarity Protection | Yes |
| Powered from Terminal Block | Yes, 12 ~ 48 VDC |
| Powered from PoE | Yes, IEEE 802.3af, Class1 |
| Consumption | 3.8 W |
| Dimensions (w x l x h) | 72 x 123 x 35mm |
| Installation | DIN-Rail or Wall Mounting |
| Operating Temperature | -25 °C ~ +75 °C |
| Storage Temperature | -30 °C ~ +80 °C |
| Humidity | 10 ~ 90% RH, non-condensing |
