Wij gebruiken cookies om uw ervaring beter te maken. Om te voldoen aan de cookie wetgeving, vragen we uw toestemming om de cookies te plaatsen. Meer informatie.
ICS GPIB-to-Serial Interface Board 4804B
Levertijd:
3~4 weken
SKU
4804B
GPIB to Serial Interface Board
● Provides user selectable single-ended RS-232 and balanced RS-422/RS-485 serial signals. Matches any asynchronous serial interface.
● Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode). Versitle interface board.
● > 600 kbyte/sec GPIB transfer rate. Reduces bus transfer time.
● GPIB/Serial configurations stored in E2PROM. Easy setup eliminates removing covers to change or check the configuration.
● GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command. User can select address setting method.
● On board regulator for operation from 5 ~ 15 VDC power. Runs off of almost any power supply.
● Designed for easy installation as an OEM interface. Not just a board without its enclosure.
● Includes Test LEDs. Provides visual indication of unit's operation and selftest status.
The Model 4804B GPIB <-> Serial Interface Board is a transparent bidirectional IEEE 488.2/GPIB to Serial Interface that is used to adapt devices with serial interfaces to the GPIB or HP-IB bus. The ICS GPIB-to-Serial Interface Board 4804B provides user selected RS-232 or RS-422 full-duplex signals at rates up to 38,4000 baud. The 4804B can also be programmed for half-duplex, two wire operation to control an RS-485 device or network. In a typical application, the ICS GPIB-to-Serial Interface Board 4804B is located inside the device chassis and is powered by a small amount of DC power from the host's power supply. The 4804B is a quick and easy way to add an IEEE-488.2 interface to any device with a RS-232 or RS-422/RS-485 serial interface.
The ICS GPIB-to-Serial Interface Board 4804B operates in either of two modes. In the G-Mode it interfaces serial devices to the GPIB bus. In the S-Mode it can control a single GPIB device from a serial source.
Meer informatie
Art.nr.
4804B
Fabrikant
ICS Electronics
Land van herkomst
Verenigde Staten
GPIB Capabilities
| IEEE 488 Bus Interface |
|
||||||
| GPIB Addresses | 0-30 primary addresses | ||||||
| SRQ Generation |
|
||||||
| Escape Sequence | In G mode the 4804B powers up in the transparent Data sub-mode. Device Trigger is used to switch from Data to Command sub-mode to query or configure the board. The SCPI SYST:OPER DATA command is used to switch back to the Data sub-mode. | ||||||
| 488.2 Common Commands | *CLS, *ESE, *ESE?, *ESR?, *IDN?, *OPC, *OPC?, *RST, *SRE, *STB, *TST?, IST?, *PRE, *PRE?, *PCB, *SRE? and *WAI | ||||||
| Buffers |
|
||||||
| 4804/4804A Compatibility | In the G-Mode, the 4804B uses the GPIB Device Trigger command to switch from Data to the Command sub-mode. The older Model 4804s and 4804As used an Listen-Unlisten escape sequence which is not recommended for use with high-speed computers. All other functions and commands are identical. |
Interface Specifications
| Serial Interface | Serial signals conform to EIA Specifications for RS-232 single or RS-485 (RS-422) differential signals. |
| Baud Rates | 300, 600, 1.2K, 2.4K, 4.8K, 9.6K,19.2K and 38.4K baud |
| Data Bits | 7 or 8 bits |
| Parity | Odd, even or none |
| Stop Bits | 1 or 2 |
| Data Transfer Protocol | |
| Hardware handshake always enabled. | |
| X-on/X-off enabled by SCSI command. | |
| SCSI Commands | The 4804B conforms to the SCPI 1994.0 Specification and uses SCPI commands to select: |
Controls and Indicators
| Test LEDs | PWR, RDY, TALK, LSTN, BUSY and BUFFER FULL |
Grootte
139.7 x 114.3 x 12.7mm (l x w x h)
Connectors and Headers
| GPIB | 24-pin 3M 2524 male connector | ||
| GPIB/Addr | 26-pin 3M 2526 male connector | ||
| Serial |
|
Omgeving
| Operating Temperature | -10 °C ~ +70 °C |
| Storage Temperature | -20 °C ~ +85 °C |
| Humidity | 0-90% RH without condensation |
Power
| Regulated +5 Vdc or Unregulated +5.5 to +15 VDC @ 300 mA (typical) |
Included Accessories
| Instruction Manual |
| Configuration Disk with sample programs. |