ICPDAS 8000 Series PAC iP-8847 is a Dual Ethernet ISaGRAF SoftLogic PAC (Programmable Automation Controller) of ICP DAS iPAC-8000 series. It is equipped with an 80186, 80 MHz CPU running a MiniOS7 operating system, various connectivity including Dual 10/100 Base-TX Ethernet Ports, one RS-232/485 port, one RS-485 port and two RS-232 ports, and 4/8 slots for high performance Parallel-type I/O modules (High profile I-8K series) and high performance Serial-type I/O modules (Hot-Swap High Profile I-87K series), etc. Compared with I-8xx7, ICPDAS 8000 Series PAC iP-8847 series is 2 ~ 4 times faster!
RS-232: TxD,RxD,RTS,CTS,DSR,DTR,CD,RI,GND. Speed: 115200 bps max. Full modem signals.
MMI (Man Machine Interface)
Modbus RTU/ASCII Master Protocol
Up to 2 COM Ports, COM1 ~ (COM5 in multi serial port board) can support Modbus RTU Master or ASCII Master protocol to connect to other Modbus Slave devices. Max. Modbus_xxx Function Block amount for 2 ports: 128.
Modbus RTU Slave
Protocol
Up to 2 COM Ports, COM1 and one of (COM2, COM3) can support Modbus RTU Slave protocol for connecting ISaGRAF, PC/HMI/OPC Server & MMI panels.
Modbus TCP/IP Slave
Protocol
2 Ethernet ports support Modbus TCP/IP Slave Protocol for connecting ISaGRAF & PC/HMI.
(Max. 6 connections)
Remote I/O
One of COM2 or COM3 or COM4 supports I-7000 I/O modules & [(I-87Kn base or RU-87P1/2/4/8)+
I-87K High Profile I/O boards] as Remote I/O. Max. 64 Remote I/O module for one PAC.
Fbus
Built-in COM3 Port to exchange data between ICP DAS's ISaGRAF PACs.
Ebus
To exchange data between ICP DAS's ISaGRAF Ethernet PACs via Ethernet port.
(The LAN2: upper port ONLY)
SMS:
Short Message Service
One of COM4 or (COM5 in multi serial port board) can link to a GSM modem to support SMS. User can request data/control the controller by cellular phone. The controller can also send data & alarms to user's cellular phone. Optional GSM/GPRS modem: GTM-201-RS232 (850/900/1800/1900 GSM/GPRS External Modem)
User-defined Protocol
User can write his own protocol applied at COM1, COM2, COM3, COM4 (& COM5 ~ COM20 if multi-serial port boards are plugged) by serial communication function blocks.
MMICON/LCD
One of COM3 or COM4 supports ICP DAS's MMICON. The MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User can use it to display picture, string, integer, float, and input a character, string, integer and float.
Redundant Bus7000
Two ISaGRAF PACs can link to remote I-7000 & I-87K High profile I/O modules at the same time. Only one controller is active to control these Remote I/Os. If one is dead, the other one will take over the control of Remote I/Os.
CAN/CANopen
iP-8x47 can use its COM1,3,4 or (COM5 ~ COM12 resides at the I-8112iW/8114W/8114iW RS-232 expansion board) to connect one I-7530 : the RS-232 to CAN converter to support CAN and CANopen devices and sensors. One iP-8x47 supports max.3 RS-232 ports to connect max.3 I-7530.
FRnet I/O
Support Max.4 I-8172W FRnet Master cards to connect FRnet I/O modules.
(Max. 1024-ch. DI + 1024-ch. DO)
Sending E-mail
Actively or passively sending E-mail via Ethernet port through internet. Max.10 receivers for each sending and can send E-mail with an attached file. (Max. file size is about 488 KB)
SMMI
Yes, on the front panel. 4 push buttons, 3 green programmable LEDs, 1 red power LED and 5-digit 7-Seg. LED (Display message, value, input value, simulate input & output.)
I/O Expansion Slots
Slot Number
8 empty slots.
Accept only High Profile I-8K Parallel & High Profile I-87K Serial I/O boards
Hot-Swap
Support Hot-Swap I-87K high profile I/O module on the slot 0 ~ 7 if the module needs to be replaced.
Motion
Motion Control
One I-8091W (2-axis) or two I-8091W (4-axis) to do motion control. Ethernet communication is also available when doing motion control.
