ICPDAS PISO-DNM100U-D

Levertijd:
2~7 dagen
SKU
PISO-DNM100U-D

1 Port Intelligent DeviceNet Master Communication Board with DeviceNet Firmware Inside

 

● DeviceNet Version: Volume I & II, Release 2.0
● Programmable Master MAC ID and Baud Rate
● Baud Rate: 125 kbps, 250 kbps, 500 kbps
● Support Group 2 and UCMM connection
● I/O Operating Modes: Poll, Bit-Strobe, Change of State / Cyclic
● I/O Length: 512 Bytes max (Input/Output) per slave
● Slave Node : 63 nodes max
● Support Auto-Search slave device function
● Support on-line adding and removing devices
● Support Auto-detect Group 2 and UCMM device

 

PISO-DNM100 can represent an economic solution of DeviceNet application and be a DeviceNet master device on the DeviceNet network. It is a "Predefined Master-Slave connection Set". PISO-DNM100 supports Group 2 only Server and UCMM functions to communication with slave devices. It has an independent CAN bus communication port and has the ability to cover a wide range of DeviceNet applications.

 

Besides, PISO-DNM100 uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function.It can be installed on almost any windows-based system, for example Win98/Win2000/WinXP. It is popularly applied in the industrial automation, building automation, vehicle, marine, and embedded control network. In order to expand the DeviceNet functions of ICPDAS products, PISO-DNM100 is developed for this purpose.

 

https://fieldworks.nl/media/imageproducts/icpdas/PISO-DNM100_1.jpg

 

APPLICATIONS

● Industrial Machinery
● Building Automation
● Medical
● Maritime
● Restaurant Appliances
● Laboratory Equipment & Research

 

https://fieldworks.nl/media/imageproducts/icpdas/wharf.gif

 

TOOLKIT

● Development Toolkit for Windows NT4.0
● Development Toolkit for Windows 98/ME
● Development Toolkit for Windows 2000/XP

 

SOFTWARE UTILITY FEATURES

 

Diagnosis

This utility supports to search all devices and specific devices in the network. These functions help the users to configure the connection of the slave devices. Anymore, the software also can diagnose the remote slave devices when building the DeviceNet network.

 

Configuration

This software supports the users to configure the I/O connection of the devices by searching devices or manual setting. After configuring the I/O connection, the information would be saved into the EEPROM. The users can export the data from the EEPROM easily. Correspondingly, the users can import the data into the EEPROM.

 

Remote I/O Access

he software utility can easily to access the I/O data of all the slave devices. The users can monitor the input data of the specific slave device and change the output data to the remote slave device with this utility.

Meer informatie
Art.nr.
PISO-DNM100U-D
Fabrikant
ICPDAS
Bus Interface
Type Universal PCI supports both 5 V and 3.3 V PCI bus
Board No. By DIP switch
CAN Interface
Controller
NXP SJA1000T with 16 MHz clock
Microprocessor inside with 80186 80MHz
Transceiver NXP 82C250
Channel Number 1
Connector 9-pin male D-Sub (CAN_GND, CAN_L, CAN_SHLD, CAN_H, N/A for others)
Baud Rate (bps) 125 k, 250 k, 500 k
Transmission Distance Depend on baud rate (for example, max. 1000 m at 50 kbps)
Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Terminator Resistor Jumper for 120 Ω terminator resistor
Specification ISO-11898-2, CAN 2.0A and CAN 2.0B
Protocol DeviceNet Volumn I v2.0, Volumn II v2.0
LED Indicators
Round LED Green LED, Red LED
Software
Driver Windows 98/ME/NT/2K/XP
Library VB 6.0, VC++ 6.0, BCB 6.0
Power
Power Consumption 300 mA @ 5 V
Mechanical
Dimensions (w x h) 138 x 127mm
Omgeving
Operating Temperature -25 °C ~ +75 °C
Storage Temperature -40 °C ~ +80 °C
Humidity 5 ~ 95% RH, non-condensing
Mijn vraag gaat over: ICPDAS PISO-DNM100U-D
To Top