Wij gebruiken cookies om uw ervaring beter te maken. Om te voldoen aan de cookie wetgeving, vragen we uw toestemming om de cookies te plaatsen. Meer informatie.
ICPDAS I-2533 - CAN/Fiber Converter
Levertijd:
2~7 dagen
SKU
I-2533
CAN/Fiber Bridge
● Fiber Port: ST (Multi-mode)
● Maximum transmission distance up to 2 km at any CAN baud rate
● 82C250 CAN transceiver
● 2500 Vrms iCoupler isolation on the CAN side
● Support both CAN 2.0A and CAN 2.0B
● Fully compatible with the ISO 11898-2 standard
● Build-in switch for 120 Ω terminator resistor
● Up to 100 CAN nodes on each channel
● Removable terminal block
● DIN-Rail Mountable
I-2533 is a local CAN bridge used to establish a connection between two CAN bus system via fiber optic transmission medium. In order to solve the problem between CAN and fiber transmission medium, I-2533 is specially designed for converting the electrical CAN bus signal to fiber optic cables. Not just like I-2532, I-2533 has three more important features.
First, the transmission distance limitation of the CAN bus system will not reduced because of CAN baud rate. It means that the total network distance can be extended. Second, the bus error on one CAN network will not affect the operation of another CAN network. Finally, the two CAN network can communication with each other by using different CAN baud rate for highly flexibility. Besides, I-2533 provides the utility tool for user-defined baud rate and filter configuration. By using this tool, it is allowed to have user-defined baud rate and message filter. When users use the I-2533 on two CAN network with different CAN baud rate, it may be useful to reduce the bus loading on the network which has low baud rate.
APPLICATIONS
● Control System
● Building Automation
● Factory Automation
● Distributed data acquisition
Meer informatie
Art.nr.
I-2533
Fabrikant
ICPDAS
CAN Interface
| Connector | Screwed terminal block (CAN_GND, CAN_L, CAN_H) |
| Baud Rate (bps) | 10 k ~ 1 M |
| Transmission Distance | Depend on baud rate |
| Terminator Resistor | Switch for 120Ω terminator resistor |
| Isolation | 2500Vrms |
| Specification | ISO-11898-2, CAN 2.0A and CAN 2.0B |
Fiber Interface
| Connector | ST (Multi-mode) |
| Wave Length | 850 nm |
| Fiber Cable | 50 / 125 μm , 62.5 / 125 μm, 100 / 140 μm (62.5 / 125μm is recommended) |
| Propagation Delay | 125ns max (125ns delay shortens bus line length by ~ 25 m) |
| Transmission Distance | 2 km max (in 62.5 / 125 μm fiber cable) |
LED Indicators
| Round LED | PWR LED, CAN_Tx LED, CAN_Rx LED, CAN_Err LED, FB_Err LED |
Power
| Power supply | Unregulated +10 ~ +30 VDC |
| Protection | Power reverse polarity protection, Overvoltage brownout protection |
| Power Consumption | 3 W |
Mechanical
| Dimensions (w x l x h) | 32.3 x 77.5 x 99.0mm |
| Installation | DIN-Rail |
Omgeving
| Operating Temperature | -25 ~ 75 °C |
| Storage Temperature | -40 ~ 80 °C |
| Humidity | 5 ~ 95% RH, non-condensing |
U bent wellicht ook geïnteresseerd in de volgende producten:
