ICS Serial to Relay Interface Module 2364

Levertijd:
3~4 weken
SKU
2364

Serial to Relay Interface Module

● Multiple relay configurations: 16 low-level SPST relays, 16 hi-power SPST relays or 16 relay drivers. Choose the right contact or relay driver for your application.
● Multiple relay programming modes: individual relays, single or multipole scanning. Flexible relay programming.
● Isolated digital inputs accept contact closures and CMOS/TTL logic levels. Eliminates ground loops.
● IEEE-488.2 compatible unit uses SCPI commands. Meets the latest GPIB specifications.
● Includes a menu-driven configuration program. Steps user thrugh configuration choices.
● Metal case provides full EMI/RFI protection. Proven EMI/RFI Compliance.

ICS Serial to Relay Interface Module 2364 is a compact, RS-232/RS-485 to Relay Interface that provides 16 form ‘A’ contacts or 16 relay drivers for switching signals or driving external relays. The ICS Serial to Relay Interface Module 2364’s versatile commands let the user control the relays individually, configure the relays as a single or multipole scanner, or configure the relays in a preset pattern as a device controller. The ICS Serial to Relay Interface Module 2364 also has eight isolated digital inputs that can be used to sense external signals or contact closures. In control applications, these signals can be used to verify the response of the external system to the control outputs. The ICS Serial to Relay Interface Module 2364 can also monitor the input signals and generate an Service Request Message when the signals change state.

Meer informatie
Art.nr.
2364
Fabrikant
ICS Electronics
Land van herkomst
Verenigde Staten
Interface Specifications

Provides RS-232 and RS-485 (RS-422) asynchronous serial interfaces. Unit responds to the serial interface that receives the command.

RS-232 Interface
Signals AB, BA and BB
Mode Full Duplex
RS-485 (RS-422) Signals
Signals TX/RX pair
Mode Half duplex with or without address detection
Addresses 0 ~ 15
Termination 220 Ω load resistor and 1 KΩ pullup/pulldown resistors
Common Specifications
Baud Rate 1200 ~ 38.4 Kbaud
Data Bits 7 or 8
Stop Bits 1 or 2
Parity Odd, Even or None
Command Sets
SCPI and short form commands plus the following IEEE 488.2 Common Commands:
*CLS, *ESE, *ESE?, *ESR, *IDN?, *OPC, *OPC?, *PSC, *PSC?, *RCL, *RST, *SAV, *SRE, *SRE?, *TRG, *TST, and *WAI.
Digital Input

Eight isolated inputs that can be queried and/or monitored for selected bit changes. Detected changes are saved and can be used to generate a Service Request (SRQ).

Data Lines 8
Input Signals TTL/CMOS or contact closure to ground
Input Levels
Low = 0±0.5 V @ 2 mA
High=>2.4 V or open 1.5 KΩ to +5 VDC or to user furnished external voltage
External Voltage 5 ~ 32 VDC
Isolation 500 VDC to internal logic with external pullup voltage
Monitoring 1,000 samples/sec.
Relay Contacts

All relay contacts are brought out to individual pins on the relay connector. Guard lines are provided between adjacent relay contacts.

Model Number 2364-11 2364-12
Usage Lo level Hi Power
Number of Relays 16
Contact Form Form A (SPST)
Contact Material Ruthenium -
Contact Ratings (Restive Load) 0.5 A 1.0 A
Switching V 200 VDC
Power 10 W 50 W
Breakdown V 300 VAC
Resistance 0.15 Ω 0.2 Ω
Life at 100μA 20 x 106 cycles
Life at 500mA 2 x 106 cycles
Relay/Solenoid Driver Outputs

In -14 version, the relays are omitted and the relay drivers are brought directly out to the connector. Drivers are open collector type with an internal snubber diode. User supplies the external voltage for the diodes.

Model Number 2364-14
Usage External Relays
Number of Drivers 16
Current 300 mA sink max.
Switching V 48 VDC max.
Scanner-sequence Memory
16 relays x 32 steps
Controls and Indicators
PWR Indicates power on
RDY Unit has passed self test
TALK Unit is addressed to talk
LSTN Unit is addressed to listen
SRQ Unit is asserting SRQ
ERR Unit sensed a command error
Grootte
1185.2 x 38.6 x 189.2mm (W x H x D)
Connectors and Headers
IEEE bus-Std 24 pin with metric studs
I/O-Amphenol 57-30500 50-pin connector with spring locks
Omgeving
Operating Temperature -10 °C to +55 °C
Storage Temperature -40 °C to +70 °C
Humidity 0-90% RH no condensation
Power
12 to 24 VDC @ 100 mA plus 10 mA per closed relay
Mechanical
Construction All metal case
Included Accessories
Instruction Manual
Mating Connector
Support CD-ROm with Configuration and example programs
UL/CSA/VDE approved AC power adapter
ICS Serial to Relay Interface Module 2364 aanpassen
Aantal

* Verplichte velden

Uw configuratie
Serial to Relay Interface Module
ICS Serial to Relay Interface Module 2364
Overzicht
    Mijn vraag gaat over: ICS Serial to Relay Interface Module 2364
    To Top