2~7 dagen

Advanced Ethernet ISaGRAF Palm-Size PAC with POE and 7-segment display

Software Features:
● MiniOS7 Embedded Operating System (DOS-like)
● ISaGRAF v3 SoftLogic Inside
● Support IEC 61131-3 Standard
● Accepts max. 64 KB ISaGRAF code size

Hardware Features:

● 80186 CPU (16-bit & 80 MHz)
● Built-in watchdog timer (WDT) to improve the system stability
● SRAM (640 KB), Flash (512 KB)
10/100M Ethernet Ports
● 2 Serial Ports (RS-232/485)
● I/O Expansion Bus Interface (support one X-board I/O expansion board)

ICPDAS μPAC-7186PEGD is a palm-size PAC and includes ISaGRAF SoftLogic. It has one 10/100 Best-TX Ethernet port, one RS-232 port and one RS-485 port. The user can choose an I/O expansion board, X-board, to expand the I/Os or memories of μPAC

ICPDAS μPAC-7186PEGD support Modbus Serial protocol, Modbus TCP/IP protocol, Modbus Master protocol, Remote I/O, Fbus, Ebus, SMS: Short Message Service, modem link, MMICON/LCD, ZigBee wireless communication, GPS application, FRnet, CAN remote I/O connection and user defined protocol. Compared with I-7188EG, μPAC-7186 is 2 ~ 4 times faster.

ICPDAS μPAC-7186PEGD is the model of μPAC-7186EGD with PoE (Power-over-Ethernet). PoE allows power and data to be carried over a single Ethernet cable, so a device can operate solely from the power it receives through the data cable. This innovation allows greater flexibility in office design, higher efficiency in systems design, and faster turnaround time in systems design, and faster turnaround time in set-up and implementation.


● ISaGRAF PAC connects the Intelligent Power Meter PM-2133/2134
● Stress Monitoring Application of Constructions
● Redundant Communication System
● eLogger HMI Application
● Redundant System with iDCS-8000
● Modbus TCP/IP Master
● ZigBee Wireless Solution
● GPS Applications: ISaGRAF PAC plus I-87211W or GPS-721
● Integrate with CAN/CANopen Devices and Sensors
● Send Email with One Attached File
● An Easy Way to Program the Fast FRnet Remote I/O Modules
● Data Acquisition Auto-Report System
● Hot-Swap and Redundant System
● Modbus RTU/TCP Slave Ports
● Modbus RTU/ASCII Master Ports
● Remote I/O Modules and Expansion module/board
● Expansion module/board
● SMS: Short Message Service
● Multiple Web HMI - Monitor & Control Everywhere!
● Motion Control
● Data Recorder and Data Logger
● Data Exchange: Fbus or Ebus
● Detect Hot-Swap I-87K (High Profile) I/O Status
● VIP Communication Security

Meer informatie
OS MiniOS7
Development Software
ISaGRAF v3 IEC61131-3 standard. Languages: LD, ST, FBD, SFC, IL & FC
Max. Code Size μPAC-7186EG/PEG accepts max.64 KB ISaGRAF code size (Appli.x8m must < 64KB)
CPU 80186 or compatible (16-bit and 80 MHz)
Watchdog Timer Yes, default 0.8 second
RTC (Real Time Clock) Provide second, minute, hour, date, day of week, month, year
FLASH Memory 512 KB, Erase unit is 64 KB, 100,000 erase/write cycles
NVRAM 31 bytes, battery backup, data valid up to 10 years
EEPROM 16 KB (16384 bytes), retention > 100 years. 1.000.000 erase/write cycles
Expansion I/O Bus One optional X-series I/O board can be plugged inside
NET ID User-assigned by software, 1 ~ 255
Display No
System LED Indicator Yes (Red/Orange)
PoE LED Indicator Yes (Green)
Communication Ports
COM1 RS-232: TxD, RxD, RTS, CTS, GND Speed: 115200 bps max. Program downloads port ; Non-isolated.
COM2 RS-485: D+, D-, 115200 bps max. Self-tuner ASIC inside, Program downloads port ; Non-isolated.
Ethernet 10/100 Mbps, NE2000 compatible, 10/100 Base-TX, Programs download port.
PWM Output
Pulse Width Modulation Output
All X-series DO boards support PWM output. 8-ch max. for one controller.
500 Hz max. for Off = 1 & On = 1 ms
Output square wave: Off: 1 ~ 32767 ms, On: 1 ~ 32767 ms
Parallel DI Counter
All X-series DO boards support DI Counter
8-channel max. for one controller. Counter value: 32-bit
500 Hz max. Min. pulse width > 1 ms
Remote DI Counter All remote I-7000 & I-87K DI modules support counters. 100 Hz max. value: 0 ~ 65535
Remote High Speed Counter Optional I-87082: 100 kHz max. ,32-bit
Modbus RTU/ASCII Master Protocol Up to 2 COM Ports (COM1, COM2 and COM3-in-X-board) support Modbus RTU/ASCII Master protocol to connect to other Modbus Slave I/O devices
Modbus RTU Slave
Up to 2 COM Ports (COM1, one of COM2 or COM3-in-X-board) can support Modbus RTU Slave protocol for connecting ISaGRAF, PC/HMI/OPC Server & MMI panels.
Modbus TCP/IP
Ethernet port supports Modbus TCP/IP Slave protocol for connecting ISaGRAF & PC/HMI.
Remote I/O One of COM2 (or COM3: RS-485 if found) supports I-7000 I/O modules & (I-87K base + I-87K serial I/O boards or RU-87P1/2/4/8 + I-87K High Profile I/O cards) as Remote I/O. Max. 64 I/O module for one controller.
Fbus Built-in COM2 Port to exchange data between ICP DAS's ISaGRAF PACs.
Ebus To exchange data between ICP DAS's ISaGRAF Ethernet PACs via Ethernet port.
Send Email Send email to maximum 10 receivers each time via internet. If applying with an X607/608 X-board, it could send email with one attached file and the maximum file size is about 488 KB for using X608 or about 112 KB for using X607.
Short Message Service
One of (COM1 or COM3: RS-232 or COM4: RS-232 if found) can link to a GSM modem to support SMS. User can request data/control the controller by cellular phone. The controller can also send data & alarms to user's cellular phone.
Optional GSM modems: GTM-201-RS232 (850/900/1800/1900 GSM/GPRS External Modem)
User-defined Protocol User can write his own protocol applied at COM1, COM2 & (COM3 ~ COM8 if found) by serial communication function blocks.
Modem Link Supports PC to remotely download & monitor the controller through COM4 of X504.
MMICON/LCD One of (COM3: RS-232 if found) supports ICP DAS's MMICON. The MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User can use it to display picture, string, integer, float, and input a character, string, integer and float.
Redundancy Solution One is Master, one is Slave. Master handles all inputs & outputs at run time. If Master is damaged (or Power off), Slave takes the control of Bus7000b. If Master is alive from damaged (or power up again), it takes the control of Bus7000b again. The change over time is about 5 seconds. Control data is exchanging via Ebus (if using a cross cable, no need any Ethernet switch). All I/O should be RS-485 I/O except the status I/O in the slot 0: X-107.
CAN/CANopen μPAC-7186EG can use its COM1 or COM3 ~ COM8 (resides at the X5xx RS-232 expansion board) to connect one I-7530: the RS-232 to CAN converter to support CAN and CANopen devices and sensors. One μPAC-7186EG supports max.3 RS-232 port to connect max. 3 I-7530.
Input Range +12 ~ +48 VDC
Protection Power reverse polarity protection
PoE IEEE 802.3af, Class 1
Power Consumption 2.5 W (when I/O slots are empty)
Dimensions (w x h x d) 72 x 123 x 35mm
Operating Temperature -25 °C ~ +75 °C
Storage Temperature -30 °C ~ +80 °C
Humidity 10 ~ 90 % RH (non-condensing)
Battery Backup SRAM
With the optional X607 or X608 board plugged inside the μPAC-7186EG/PEG, data can be stored in it, and then PC can load these data via COM1 or Ethernet. PC can also download pre-defined data to X607/608. Optional: X607: 128 KB, X608: 512 KB
Mijn vraag gaat over: ICPDAS μPAC-7186PEGD
To Top