2~7 dagen

4 slots Faster CPU (80 MHz) Dual Ethernet ISaGRAF PAC

● MiniOS7 Embedded Operating System (DOS-like)
● ISaGRAF Ver.3 SoftLogic Inside
● Support IEC 61131-3 Standard
● Accepts max. 64 KB ISaGRAF code size

● 80186 CPU (16-bit & 80 MHz)
● Dual Battery Backup SRAM (512 KB)
● 64-bit Hardware Serial Number for Protection
● 4 Expansion Slots (support High Profile I/O Modules)
● Support I/O Module Hot Swap
● Dual 10/100M Ethernet Ports
● 4 Serial Ports (RS-232/485)
● Redundant Power Inputs

<p>ICPDAS 8000 Series PAC iP-8447 is a Dual Ethernet ISaGRAF SoftLogic PAC (Programmable Automation Controller) of ICP DAS iPAC-8000 series.  It is equipped with an 80186, 80 MHz CPU running a MiniOS7 operating system, various connectivity including Dual 10/100 Base-TX Ethernet Ports, one RS-232/485 port, one RS-485 port and two RS-232 ports, and 4/8 slots for high performance Parallel-type I/O modules (High profile I-8K series) and high performance Serial-type I/O modules (Hot-Swap High Profile I-87K series), etc. Compared with I-8xx7, ICPDAS 8000 Series PAC iP-8447 is 2 ~ 4 times faster!</p>

Meer informatie
OS MiniOS7
Development Software
ISaGRAF Software ISaGRAF v3: IEC 61131-3 standard. Languages: LD, ST, FBD, SFC, IL & FC
Max. Code Size Accepts max. 64 KB ISaGRAF code size (Appli.x8m must < 64 KB)
CPU 80186, 80 MHz (16-bit) or compatible.
Watchdog Timer Yes, Default = 0.8 second
RTC (Real Time Clock) Provide second, minute, hour, date, day of week, month, year
Dual Battery Backup SRAM 512 KB (for 5 years data retention), support up to 1024 retain variables.
FLASH Memory 512 KB, 100.000 erase/write cycles with Flash protection switch.
NVRAM 31 bytes, battery backup, data valid up to 5 years.
EEPROM 16K, retention > 40 years; 1.000,000 erase/write cycles.
Serial Number Yes, 64-bit Hardware Serial Number.
NET ID 8-pin DIP switch to set NET ID as 1 ~ 255.
Communication Ports
RJ-45 x 2, 10/100 Base-TX, Programs download port.
(Auto-negotiating, Auto MDI/MDI-X, LED indicators)
COM1 RS-232: TxD, RxD, GND; Speed: 115200 bps max. Program downloads port.
COM2 RS-485: D+, D-; Speed: 115.200 bps max.; 3000 VDC Isolated
RS-232/485; RS-232: TxD,RxD,RTS,CTS,GND, RS-485: D+, D-
Speed: 115200 bps max. Program downloads port.
COM4 RS-232: TxD,RxD,RTS,CTS,DSR,DTR,CD,RI,GND. Speed: 115200 bps max. Full modem signals.
MMI (Man Machine Interface)
Modbus RTU/ASCII Master Protocol Up to 2 COM Ports, COM1 ~ (COM5 in multi serial port board) can support Modbus RTU Master or ASCII Master protocol to connect to other Modbus Slave devices. Max. Modbus_xxx Function Block amount for 2 ports: 128.
Modbus RTU Slave
Up to 2 COM Ports, COM1 and one of (COM2, COM3) can support Modbus RTU Slave protocol for connecting ISaGRAF, PC/HMI/OPC Server & MMI panels.
Modbus TCP/IP Slave
2 Ethernet ports support Modbus TCP/IP Slave Protocol for connecting ISaGRAF & PC/HMI.
(Max. 6 connections)
Remote I/O One of COM2 or COM3 or COM4 supports I-7000 I/O modules & [(I-87Kn base or RU-87P1/2/4/8)+
I-87K High Profile I/O boards] as Remote I/O. Max. 64 Remote I/O module for one PAC.
Fbus Built-in COM3 Port to exchange data between ICP DAS's ISaGRAF PACs.
Ebus To exchange data between ICP DAS's ISaGRAF Ethernet PACs via Ethernet port.
(The LAN2: upper port ONLY)
Short Message Service
One of COM4 or (COM5 in multi serial port board) can link to a GSM modem to support SMS. User can request data/control the controller by cellular phone. The controller can also send data & alarms to user's cellular phone. Optional GSM/GPRS modem: GTM-201-RS232 (850/900/1800/1900 GSM/GPRS External Modem)
User-defined Protocol User can write his own protocol applied at COM1, COM2, COM3, COM4 (& COM5 ~ COM20 if multi-serial port boards are plugged) by serial communication function blocks.
MMICON/LCD One of COM3 or COM4 supports ICP DAS's MMICON. The MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User can use it to display picture, string, integer, float, and input a character, string, integer and float.
Redundant Bus7000 Two ISaGRAF PACs can link to remote I-7000 & I-87K High profile I/O modules at the same time. Only one controller is active to control these Remote I/Os. If one is dead, the other one will take over the control of Remote I/Os.
CAN/CANopen iP-8x47 can use its COM1,3,4 or (COM5 ~ COM12 resides at the I-8112iW/8114W/8114iW RS-232 expansion board) to connect one I-7530 : the RS-232 to CAN converter to support CAN and CANopen devices and sensors. One iP-8x47 supports max.3 RS-232 ports to connect max.3 I-7530.
FRnet I/O Support Max.4 I-8172W FRnet Master cards to connect FRnet I/O modules. (Max. 1024-ch. DI + 1024-ch. DO)
Sending E-mail Actively or passively sending E-mail via Ethernet port through internet. Max.10 receivers for each sending and can send E-mail with an attached file. (Max. file size is about 488 KB)
Yes, on the front panel. 4 push buttons, 3 green programmable LEDs, 1 red power LED and 5-digit 7-Seg. LED (Display message, value, input value, simulate input & output.)
I/O Expansion Slots
Slot Number
4 empty slots.
Accept only High Profile I-8K Parallel & High Profile I-87K Serial I/O boards
Hot-Swap Support Hot-Swap I-87K high profile I/O module on the slot 0 ~ 7 if the module needs to be replaced.
Motion Control One I-8091W (2-axis) or two I-8091W (4-axis) to do motion control. Ethernet communication is also available when doing motion control.
PWM Output
High Speed PWM Module I-8088W:
8-channel PWM outputs, software support 1 Hz ~ 100 KHz (non-continuous), duty: 0.1 ~ 99.9%
DO Module as PWM
8-channel max. for one controller. 500 Hz max. For Off = 1 & On = 1 ms Output square wave: Off: 1 ~ 32767 ms, On: 1 ~ 32767 ms.
Optional DO Boards: I-8037W, 8041W, 8041AW, 8042W, 8050W, 8054W, 8055W, 8056W, 8057W, 8060W, 8063W, 8064W, 8068W, 8069W. (Relay Output boards cannot generate fast square wave )
Parallel DI Counter
8-channel max. for 1 controller. Counter Val: 32-bit.; 500 Hz max. Min. ON & OFF width must >1ms
Optional DI boards: I-8040W, 8040PW, 8042W, 8046W, 8050W, 8051W, 8052W, 8053W, 8053PW, 8054W, 8055W, 8058W, 8063W.
Serial DI Counter
Counter input: 100 Hz max. Counter value: 0 ~ 65535 (16-bit)
Optional serial I-87K DI boards: I-87040W, 87046W, 87051W, 87052W, 87053W, 87053W-A5, 87054W, 87055W, 87058W, 87059W, 87063W.
Remote DI Counter All remote I-7000 & I-87K DI modules support counters. 100 Hz max. value: 0 ~ 65535.
High Speed Counter
I-87082W 100 kHz max. 32 bit
I-8084W 250 kHz max. 32 bit
I-8093W 3-axis Encoder Module, max. 1M Hz for quadrant input mode, max. 4M Hz for pulse/direction and cw/ccw input mode.
I-8084W 250 kHz max., 4-ch encoder, can be pulse/direction, or Up/Down or A/B phase (Quad. mode); Not support Encoder Z-index.
I-87082W 2-channel, 1 Hz ~ 100 kHz
I-8084W 8-channel, 1 Hz ~ 250 kHz
Input Range +10 ~ +30 VDC
Isolated 1 kV
Redundant Power Inputs Yes, with one power relay (1 A @ 24 VDC) for alarm.
Capacity 0.85 A, 5 V supply to CPU; 5.51 A, 5 V supply to I/O expansion slots, 30 W in total.
Power Consumption 6.7 W (0.28 A @ 24 V)
Dimensions (w x l x h) 230 x 132 x 98mm
Operating Temperature -25 ~ +75 °C
Storage Temperature -30 ~ +80 °C
Humidity 10 ~ 90 % RH (non-condensing)
Mijn vraag gaat over: ICPDAS PAC iP-8447
To Top