Wij gebruiken cookies om uw ervaring beter te maken. Om te voldoen aan de cookie wetgeving, vragen we uw toestemming om de cookies te plaatsen. Meer informatie.
ICS Digital Interface Board 4823B
Levertijd:
3~4 weken
SKU
4823B
GPIB to Parallel Digital Interface Board
● Provides a user-definable, 56-line parallel interface with bit, byte, pulse, string and binary data transfer capabilities. Fully configurable to the user's needs by bus commands.
● High-current drivers and input pullup resistors. Drives more devices, longer lines and inputs CMOS signals or switch contacts.
● Signal monitor feature detects and reports signal changes on 15 inputs. Relieves controller of time consuming polling.
● Device configuration, user's IDN message and bus address stored in Flash. Stored setup eliminates program initialization statements.
● Lock feature prevents accidental loss or change of user configuration. Protects your configuration and IDN message.
● Packaged on 3U VME size card with 4823A pinouts. Can be used to replace 4823A cards in 56 line applications.
The Model 4823B GPIB <-> Digital Interface Board is an IEEE-488.2/GPIB to digital interface with 56 I/O lines that can be used to easily adapt devices with digital signals to the IEEE-488/GPIB or HP-IP bus. In a typical application, the ICS Digital Interface Board 4823B is located inside the device chassis and is powered by the device's +5 volt power. All digital signal connections are on a 96-pin right-angle DIN connector at one end of the card. A 26-pin header on the other end of the ICS Digital Interface Board 4823B contains the GPIB Bus and address switch input signals. The header connects to a companion GPIB Connector/Address Switch Board that mounts a GPIB Connector and Address Switch on the rear panel of the chassis.
ICS Digital Interface Board 4823B are also available with optional vertical and circuit-side DIN connectors to facilitate piggybacking the 4823B on a larger PC board. The 4823B's pinouts match the first 56 pins of ICS's earlier 4823A card so that the 4823B can be used as a replacement for the 4823A in applications that use no more than 56 I/O lines.
Meer informatie
Art.nr.
4823B
Fabrikant
ICS Electronics
Land van herkomst
Verenigde Staten
GPIB Capabilities
| IEEE 488 Bus Interface |
|
||
| Address Capability |
|
||
| SRQ Generation | SRQs are generated if the unit is not a talker, if SRQs are enabled and if an Enabled Event Status Register bit or if a monitored digital input change occurs. Digital inputs monitored by the Questionable registers. | ||
| 488.2 Common Commands | *CLS, *ESE, *ESE?, *ESR?, *IDN?, *OPC, *OPC?, *RCL, *RST, *SAV, *SRE,*SRE?, *STB, TST? and *WAI | ||
| SCPI Commands | Used to set and query all programmable functions. The 4823B conforms to SCPI 1994.0 Specification. |
Interface Specifications
| Signal Characteristics | The 4823B's parallel I/O signals have the following electrical characteristics. All time delays listed here are maximums, all pulse widths are minimums. | ||||
| Inputs | 56 Digital I/O, 2 Status and Reset Inputs | ||||
| Input Logic Levels |
|
||||
| Input Timing | External Data Inhibit line SETS within 1 μs of the active edge of the EDR Input signal and resets after data is loaded. Data loading time for 6 BCD/HEX characters is 0.15 ms (typ.) after the 4823B has been addressed as a Talker. | ||||
| Output Logic Levels |
|
||||
| Output Timing | Data is transferred to the output 0.6 to 5.3 ms after receipt of a terminator depending upon transfer method. | ||||
| Data Stb | Output pulse width, 5 μs | ||||
| Trigger | Output pulse width, 5 μs | ||||
| Remote | Output level asserted when in the remote state | ||||
| Reset | Output pulse width, 40 μs for *RST command and true during 4823B reset time (70 ms) |
Digital Input
| Reset Inputs | The 4823B is reset by a low going pulse on the External Reset input line or by pressing a miniature push-button on front edge of the 4823B's PCB |
Controls and Indicators
| Diagnostic Indicators | Six on board LEDs: |
| PWR | On when power applied |
| RDY | On when self test passed |
| TALK | On when addressed to talk |
| LSTN | On when addressed to listen |
| SRQ | On when asserting SRQ line |
| ERR | On when ESR error bits set |
Grootte
160 x 100 x 15mm (l x w x h)
Connectors and Headers
| GPIB/Addr | 26-pin 3M 2526 male connector. |
| Digital I/O | 96-pin, 3 row male DIN connector |
Omgeving
| Operating Temperature | -10 °C ~ +70 °C |
| Storage Temperature | -20 °C ~ +85 °C |
| Humidity | 0-90% RH without condensation |
Power
+5 Vdc @ 400 mA (typical)
Included Accessories
| Instruction Manual |
| Configuration CD with sample programs |