ICPDAS NSM-206FT

Levertijd:
2~7 dagen
SKU
NSM-206FT

Unmanaged 4-Port Industrial 10/100 Base-T(X) with Dual 100 Base-FX Switch

 

● Automatic MDI / MDI-X crossover for plug-and-play
● Each port supports both 10/100 Mbps speed auto negotiation
● Store-and-forward architecture
● Full duplex IEEE 802.3x and half duplex backpressure flow control
● 1.6 Gbps high performance memory bandwidth
● Redundant Power Inputs +10 ~ +30V DC
Power failure alarm by relay output
● Supports operating temperatures from 0 °C ~ +70 °C
● IP20, rugged high-strength metal case
● DIN-Rail and Wall Mounting

 

The NSM-206FT (ST Connector; Multi-mode) is a Unmanaged 4-Port Industrial 10/100 Base-T(X) with Dual 100 Base-FX Switch that secures data transmission by using fiber optic transmission to provide immunity from EMI/RFI interference. It is used Ethernet for transmitting a signal up to 2 Km, and is the perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.

The NSM-206FT operates at either half or full duplex mode. In full duplex mode, range is 2km with 62.5/ 125μm fiber cables; in half duplex mode, range is 412m with 62.5/ 125μm fiber cables.

The NSM-206FT can extend your LAN in a daisy chain configuration.

NSM-206FT provides two power inputs that can be connected simultaneously to live DC power sources. If one of the power inputs fails, the other live source acts as a backup to automatically support the NSM-206FT's power needs.

Meer informatie
Art.nr.
NSM-206FT
Fabrikant
ICPDAS
Technology
Standards IEEE802.3, 802.3u, 802.3x
Processing Type Store & forward wire speed switching - no delays
MAC Addresses 1024
Memory Bandwidth 1.6 Gbps
Flow Control IEEE802.3x flow control, back pressure flow control
Interface
RJ45 port 10/100BaseT(X) auto negotiation speed, F/H duplex mode,
and auto MDI/MDIX connection
Fiber Optic port 100 Base-FX(Multi-mode; ST connector)
LED Indicators 10/100M, Link/Act, Full duplex/Half duplex(Fiber Port)
Ethernet Isolation 1500Vrms 1 minute
Frame Ground for EMS Protection Yes
Fiber Optic
Multi mode fiber cables: 50/125, 62.5/125 or 100/140 μm
Distance: 2 km, (62.5/125 μm recommended) for full duplex
Wavelength: 1300 or 1310nm
Min. TX Output: -20 dBm
Max. TX Output: -14 dBm
RX Sensitivity: -34 to -31 dBm
Ethernet Transmission Distance
Ethernet: 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm
Fast Ethernet: 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm
Power
Redundant Input Range +10 ~ +30VDC (Non-isolation)
Alarm Contact One relay output with current carrying capacity of 2A @ 30 VDC
Power consumption 0.24 A@24 VDC, ±5% arrowed with 100M Full duplex
LED Indicators Power input1, Power input2, Power fail
Protection Power reverse polarity protection
Frame Ground for EMS Protection Yes
Connection 7-Pin Removable Terminal Block
Mechanical
Case Metal
Environmental rating IP20
Dimensions (w x h x d) 72.5 x 110 x 102mm
Installation DIN-Rail or Wall Mounting
Environmental
Operating Temperature 0 °C ~ +70 °C
Storage Temperature -20 °C ~ +85 °C
Humidity 10% ~ 90% non-condensing
Mijn vraag gaat over: ICPDAS NSM-206FT
To Top