Signal Conditioning Module DI-8B38-35

Levertijd:
3~4 weken
SKU
DI-8B38-35

DI-8B38 Strain Gage Input Module (Wide (8kHz) and Narrow (3Hz) Bandwidth)

● Provides gain and excitation for strain gage-based transducers (load cells, pressure sensors, torque meters, etc.)
● Interfaces to 100Ω Thru 2kΩ Full-Bridge Strain Gages (model dependent)
● High Level Voltage Outputs
● 1500Vrms Transformer Isolation
● ANSI/IEEE C37.90.1 Transient Protection
● Input Protected up to 240VAC Continuous
● 100dB CMR
● 3Hz or 8kHz Signal Bandwidth
● ±0.05% Accuracy
● ±0.02% Linearity
● Low Drift with Ambient Temperature
● UL, CSA, FM and CE Certifications Pending
● Mix and Match Modules

DI-8B modules are an optimal solution for monitoring real-world process signals and providing high level signals to a data acquisition system. Each DI-8B38 module isolates, filters and amplifies a full-bridge strain gage input signal and provides an analog voltage output.

 

The 8B38 can interface to tranducers with a nominal resistance of 100Ω to 2kΩ depending upon the model. Bridge excitation is provided from the module with a stable 10.00V or 3.33V source. Full scale sensitivities of 2mV/V and 3mV/V are offered as standard.

 

Signal filtering is accomplished with a five-pole filter optimized for time and frequency response which provides 100dB per decade of normal-moderejection above the filter cutoff frequency. One pole of this filter is on the field side of the isolation barrier for anti-aliasing, and the other four are on the system side.

 

A special input circuit on the DI-8B38 module provides protection against accidental connection of power-line voltages up to 240VAC. Clamp circuits on the I/O and power terminals protect against harmful transients.

 

Isolation is provided by optical coupling to suppress transmission of common mode spikes or surges. The module is powered from +5VDC, ±5%.

 

The modules are designed for installation in Class I, Division 2 hazardous locations and have a high level of immunity to environmental noise.

Meer informatie
Art.nr.
DI-8B38-35
Fabrikant
Dataq Instruments
Input Range
-100°C to +100°C (DB-8B35-01)
0°C to +100°C (DB-8B35-02)
0°C to +200°C (DB-8B35-03)
0°C to +600°C (DB-8B35-04)
Bandwidth
-3dB 3kHz
Output Range
0 to +5V
Sensor Excitation Current
0.25mA
Algemeen
Input Resistance
Normal 50MΩ
Power Off 200kΩ
Overload 200kΩ
Input Protection
Continuous¹ 240VAC
Transient ANSI/IEEE C37.90.1
Lead Resistance Effect ±0.005˚C/Ω²
CMV, Input to Output 1500Vrms max
Transient, Input to Output ANSI/IEEE C37.90.1
CMR (50Hz or 60Hz) 120dB
NMR 70dB at 60Hz
Accuracy³
Please (DI-8B35-01)
Refer to (DI-8B35-02)
Ordering (DI-8B35-03)
Guide (DI-8B35-04)
Stability
Output Offset ±20ppm/ºC
Gain ±50ppm/ºC
Noise (Output, 100kHz) 200μVrms
Response Time, 90% Span 150ms
Output Protection (Transient) ANSI/IEEE C37.90.1 (Continuous Short to Ground)
Power Supply Voltage +5VDC ±5%
Power Supply Current 25mA
Power Supply Sensitivity ±25ppm/%
Dimensions 28.1 x 41.9 x 10.2mm
Operating Temperature -40ºC to +85ºC
Storage Temperature -40ºC to +85ºC
Humidity 0 to 95% Noncondensing
RTD Standards
Type 100Ω Pt
Alpha Coeeficient 0.00385
¹240VAC between + and - -/+EXC/-EXC terminals. 120VAC between - and +EXC/-EXC terminals and between +EXC and -EXC terminals.
²Ω refers to the resistance in one lead.
³Includes conformity, hysteresis and repeatability.
Mijn vraag gaat over: Signal Conditioning Module DI-8B38-35
U bent wellicht ook geïnteresseerd in de volgende producten:
To Top